NetApp FAS2240の初期設定(7-mode,HA版)

Data ONTAP (dtk-fas22404-a.)
login:
Password:

dtk-fas22404-a> setupThe setup command will rewrite the /etc/rc, /etc/exports,
/etc/hosts, /etc/hosts.equiv, /etc/dgateways, /etc/nsswitch.conf,
and /etc/resolv.conf files, saving the original contents of
these files in .bak files (e.g. /etc/exports.bak).
Are you sure you want to continue? [yes] yes NetApp Release 8.1.4 7-Mode: Wed Nov 20 16:16:17 PST 2013
System ID: XXXXXXXXXX (dtk-fas22404-a); partner ID: XXXXXXXXXX (dtk-fas22404-b)
System Serial Number: 4500000XXXXX (dtk-fas22404-a)
System Rev: D4
System Storage Configuration: Multi-Path HA
System ACP Connectivity: Full Connectivity
slot 0: System Board
Processors: 4
Processor type: Intel(R) Xeon(R) CPU C3528 @ 1.73GHz
Memory Size: 6144 MB
Memory Attributes: Hoisting
Normal ECC
Controller: A
Service Processor Status: Online
slot 0: Internal 10/100 Ethernet Controller
e0M MAC Address: 00:a0:98:52:97:XX (auto-100tx-fd-up)
e0P MAC Address: 00:a0:98:52:97:XX (auto-100tx-fd-up)
slot 0: Quad Gigabit Ethernet Controller 82580
e0a MAC Address: 00:a0:98:52:97:XX (auto-1000t-fd-up)
e0b MAC Address: 00:a0:98:52:97:XX (auto-1000t-fd-up)
e0c MAC Address: 00:a0:98:52:97:XX (auto-1000t-fd-up)
e0d MAC Address: 00:a0:98:52:97:5b (auto-1000t-fd-up)
slot 0: Interconnect HBA: Mellanox IB MT25204
slot 0: SAS Host Adapter 0a
Please enter the new hostname [dtk-fas22404-a]: 24 Disks: 20341.3GB
1 shelf with IOM6E
　　slot 0: SAS Host Adapter 0b
24 Disks: 20341.3GB
　　　1 shelf with IOM6E
　　slot 0: Intel ICH USB EHCI Adapter u0a (0xdf101000)
boot0 Micron Technology 0x655, class 0/0, rev 2.00/11.10, addr 2 1936MB 512B/sect (B8F0022700127488)
Please enter the new hostname [dtk-fas22404-a]: <ホスト名>
Do you want to enable IPv6? [n]: n
Do you want to configure interface groups? [n]: y
Number of interface groups to configure? [0] 2
Name of interface group #1 []: vif1
Is vif1 a single [s], multi [m] or a lacp [l] interface group? [m] l
Is vif1 to use IP-based [i], MAC-based [m], Round-robin based [r] or Port based [p] load balancing? [i] i
Number of links for vif1? [0] 2
Name of link #1 for vif1 []: e0a
Name of link #2 for vif1 []:　e0c
Name of interface group #2 []: vif2
Is vif2 a single [s], multi [m] or a lacp [l] interface group? [m] l
Is vif2 to use IP-based [i], MAC-based [m], Round-robin based [r] or Port based [p] load balancing? [i] i
Number of links for vif2? [0] 2
Name of link #1 for vif2 []: e0b Name of link #2 for vif2 []:　e0d Please enter the IP address for Network Interface vif1 []: <表LANのIPアドレス>
Please enter the netmask for Network Interface vif1 [255.255.255.0]: <表LANのサブネットマスク>
Should interface group vif1 take over a partner interface group during failover? [n]: y
Please enter the partner interface name to be taken over by vif1 []: vif1
Please enter media type for vif1 {100tx-fd, tp-fd, 100tx, tp, auto (10/100/1000)} [auto]: auto
Please enter the IP address for Network Interface vif2 []:<裏LANのIPアドレス>
Please enter the netmask for Network Interface vif2 [255.255.255.0]: <裏LANのサブネットマスク>
Should interface group vif2 take over a partner interface group during failover? [n]: y
Please enter the partner interface name to be taken over by vif2 []: vif2
Please enter media type for vif2 {100tx-fd, tp-fd, 100tx, tp, auto (10/100/1000)} [auto]: auto
e0M is a Data ONTAP dedicated management port.

NOTE: Dedicated management ports cannot be used for data
protocols (NFS, CIFS, iSCSI, NDMP or Snap*),
and if they are configured they should be on an isolated management LAN.
The default route will use dedicated mgmt ports only as the last resort,
since data protocol traffic will be blocked by default.
Please enter the IP address for Network Interface e0M []: <管理用IPアドレス>
Please enter the netmask for Network Interface e0M [255.255.255.0]: 上記アドレスのサブネットマスク
Should interface e0M take over a partner IP address during failover? [n]: y
Please enter the IPv4 address or interface name to be taken over by e0M []:
Please enter the name or IP address of the IPv4 default gateway [10.12.165.253]: デフォルトゲートウェイのIPアドレス
　　The administration host is given root access to the filer's
　　/etc files for system administration. To allow /etc root access
to all NFS clients enter RETURN below.
Please enter the name or IP address of the administration host:
Please enter timezone [Asia/Tokyo]:
Where is the filer located? []: 設置場所（適当な英文字）
What language will be used for multi-protocol files (Type ? for list)?: ja_JP.PCK_v2

Setting language on volume vol0
Language set on volume vol0
Enter the root directory for HTTP files [/vol/vol0/home/http]:
Do you want to run DNS resolver? [n]:
Do you want to run NIS client? [n]:
The Service Processor (SP) provides remote management capabilities
including console redirection, logging and power control.
It also extends autosupport by sending
additional system event alerts. Your autosupport settings are used
for sending these alerts via email over the SP LAN interface.
Would you like to configure the SP LAN interface [y]:
Would you like to enable DHCP on the SP LAN interface [y]:
The mail host is required by your system to send SP
alerts and local autosupport email.
Please enter the name or IP address of the mail host [mailhost]:
You may use the autosupport options to configure alert destinations.
The initial aggregate currently contains 3 disks; you may add more
disks to it later using the "aggr add" command.

Now type 'reboot' for changes to take effect.
dtk-fas22404-a> reboot

Do you want to configure interface groups? [n]:

Number of interface groups to configure? [0]

Name of interface group #1 []:

Is vif1 a single [s], multi [m] or a lacp [l] interface group? [m]

Is vif1 to use IP-based [i], MAC-based [m], Round-robin based [r] or Port based [p] load balancing? [i]

Should interface group vif1 take over a partner interface group during failover? [n]:

Please enter the partner interface name to be taken over by vif1 []: